12-05-2021, 10:22 PM
Short Review About All Types of Busbar Bending Machines Facilities
Busbar bending systems are produced to facilitate bending busbars for switch boards and switch gears manufacturers these systems are present in 4 types:
1-Manual busbar bending tools
2-Hydraulic busbar bending tools
3- Simple hydraulic busbar bending machines.
4-Professional busbar bending machines.
At Manual tools operator should bend busbar via hand force and it is suitable just for small size if busbars, it could bend busbars at normal axis and measurement is possible just with operator eyes . repeatability and accuracy depends on operator skills.
At hydraulic busbar bending machine and tool, We have some condition for accuracy and repeatability but operator needs low force for doing job. This type is suitable for sites or places that electricity is not available and for small jobs.
Simple hydraulic busbar bending machines are a good choice for small shops or factories that need bending busbar processing machine in normal axis away. Measurement of angles are by mechanical or digital angel indicators. Mostly they have “V” type head that cause two lines behind of busbar after bending they don’t calculate spring back and operator should consider and compensate this fault at bending process.
Professional busbar bending machines are suitable for Professional usurers.Bending head is powered with two routable plates to prevent any damage at surface of bus bar after bending. It has high technology angel measurement system that calculate spring back (spring back compensation system) and final bends adapt to desired angel with high accuracy. That’s why at, switch gears geowy we are faced to various types of bending requirements this machine should response to most of them.
Edge bending mold:
At switch gears some time designer needs to bend busbars from edge especially at electrical keys they need more space for connection’s and edge bending allow them to have enough space. Edge bending mold is a good solvation for this purpose and installable at professional busbar bending machines head. It should keep two main surface of busbar to prevent any bulge at surfaces.
Step Mold:
In some drawing designers need two closed bends in bus bar and it is not possible to do job with normal head, in these cases step mold bend two bending in one step and result is perfect.
Twist bending mold:
In some case direction of busbar machine connections are not in the same directions and mostly operators have to use several pieces of busbars. So by twist bending Mold it is possible to twist auto busbar processing machine up to go degree.
Mold for short legs bens:
This mold allow operator to bends too closed to end of busbars and busbar mold.
Busbar bending systems are produced to facilitate bending busbars for switch boards and switch gears manufacturers these systems are present in 4 types:
1-Manual busbar bending tools
2-Hydraulic busbar bending tools
3- Simple hydraulic busbar bending machines.
4-Professional busbar bending machines.
At Manual tools operator should bend busbar via hand force and it is suitable just for small size if busbars, it could bend busbars at normal axis and measurement is possible just with operator eyes . repeatability and accuracy depends on operator skills.
At hydraulic busbar bending machine and tool, We have some condition for accuracy and repeatability but operator needs low force for doing job. This type is suitable for sites or places that electricity is not available and for small jobs.
Simple hydraulic busbar bending machines are a good choice for small shops or factories that need bending busbar processing machine in normal axis away. Measurement of angles are by mechanical or digital angel indicators. Mostly they have “V” type head that cause two lines behind of busbar after bending they don’t calculate spring back and operator should consider and compensate this fault at bending process.
Professional busbar bending machines are suitable for Professional usurers.Bending head is powered with two routable plates to prevent any damage at surface of bus bar after bending. It has high technology angel measurement system that calculate spring back (spring back compensation system) and final bends adapt to desired angel with high accuracy. That’s why at, switch gears geowy we are faced to various types of bending requirements this machine should response to most of them.
Edge bending mold:
At switch gears some time designer needs to bend busbars from edge especially at electrical keys they need more space for connection’s and edge bending allow them to have enough space. Edge bending mold is a good solvation for this purpose and installable at professional busbar bending machines head. It should keep two main surface of busbar to prevent any bulge at surfaces.
Step Mold:
In some drawing designers need two closed bends in bus bar and it is not possible to do job with normal head, in these cases step mold bend two bending in one step and result is perfect.
Twist bending mold:
In some case direction of busbar machine connections are not in the same directions and mostly operators have to use several pieces of busbars. So by twist bending Mold it is possible to twist auto busbar processing machine up to go degree.
Mold for short legs bens:
This mold allow operator to bends too closed to end of busbars and busbar mold.